*DISCONTINUED* Go-Cart is not manufactured anymore! (was $967)

Ken-Bar 6hp Entry-Level Single Seat Go Cart Slight jump up from a beginner Cart this Ken-Bar model S-356 Go-Cart serves the young crowd with an Age range of 8-12 years. The S-356 is a very sensible and safe machine for a step up (from a beginners model) with tested speeds right around 25mph.The baked-on polyurethane powder coat black finish has a single seat with a perfect seat to pedal distance relative to this drivers age group. A dependable Tecumseh 6hp engine with a Centrifugal Automatic Clutch (no shifting) and a single wheel drive system for quicker and tighter responsive turns. Free Helmet and Safety Video included.

Go Cart Specs Engine Tecumseh power sport 4-cycle, OHV, air cooled, gas powered engine Startability easy - pull recoil starter - capacitor discharge Ignition Horsepower 6 hp Displacement 172 cc (10.49 cu in) Overhead valve Ignition cdi electronic Governor system quick response mechanical governor Gas tank no rust poly fuel tank Lubrication splash Exhaust system aluminized large quiet Drive System Single wheel drive, The engine drives one rear wheel so the go-kart will handle tight turns easily Drive system centrifugal clutch Brake band Seat Single padded for one individual Adjustable 7" Performance All ball bearing (front & rear) this gives longer life and the hi-speed sealed bearings never need lubrication Top speed 24 mph (approximate) Heavy duty & smooth heavy duty #420 final drive chain ensures smooth power delivery Tires Front 13/ 500 X 6" Rear 13/ 500 X 6" Frame Thick-walled steel strong 1" 11 gauge high quality steel tube Heavy gauge (thicker) frame most kart frames look the same from the outside, but there are major differences. Ken-Bar frames are made from extra-heavy duty 11 gauge steel. Many manufacturers use 14 or 16 gauge (the higher the number, the thinner it is), and some even use 18 gauge. All jig welded frames for accuracy Finish baked - on polyurethane powder coat Safety Safety video Included with kart Seat belt (adjustable) Foam padded brush bars helps to protect the occupants against tree limbs. Safety flag One free helmet Included with kart Dimensions Height 40 1/2" Length 60 1/2" Width 40" Ground clearance 4 3/4" Distance to pedals 35 3/4" Weight 190lbs Available Colors BLACK ONLY Go Cart Features Engine stop switch by steering wheel & on side of engine Side guard side bars help protect the occupants Free helmet! and safety video with every Ken-Bar Go Cart Purchase Standard features found on all Ken-Bar Go-Carts All jig welded frames for accuracy! All ball bearing axles for long life! Powder paint for durability and finish! Seat belts on all vehicles! Brush Bars standard on all models Foam covered brush bars on most models Engines by Tecumseh! Torque converter by Comet! Clutches by Max-Torq! Go Cart Notes • Unit comes 95% pre-assembled. Very minor assembly only, usually way less than an hour with normal household tools. Please read and understand your owners & safety manual, view your safety video tape (included) and then get ready for some major fun! • Speed and range specs are averaged, your ratings & experience may differ slightly. Warning! Go Carts & Mini-Bikes can be hazardous to operate. Failure to understand and follow Warnings and Instructions for the safe use and maintenance of this product may result in Death or Injury! For your safety: Always wear an approved helmet, eye protection and protective clothing. Avoid stationary objects and obstacles that create the potential for collision. Avoid excessive speed and be particularly careful on difficult terrain. Never carry passengers. Never engage in stunt riding, jumping, or operate the vehicle under the influence of drugs or alcohol. Go-Carts & Mini-Bikes are for off road use only! Competent adult supervision is recommended when children are operating the vehicle. Check state and local laws for legal operation. Read Operator’s Manual and watch Safety Video. Go-Karts R us assumes no responsibilities or liabilities from the use or mis-use of this or any of our listings sold on this site. Use of this vehicle with age requirements is listed above in the items listing. Ken-Bar Go Carts & Mini-Bikes comply with all standards for safety and performance per ANSI/SVIA-2001. Warranty & Parts Go-Cart Parts Ken-bar Manufacturing warrants to the original purchaser of its Go-Karts or Mini-bike, that if any part or parts (except engine) prove to be defective in materials and/or workmanship within 90 days. Bearing, wheel hubs, rims, chains, tie rod ends, steering spindles, throttle and brake pedals, brake drums and brake bands. No warranty on belts, clutches, throttle cables, worn out tires, and bent axles. One year warranty on frame breakage. Wrecked or abused, no warranty. Phone Ken-bar Mfg. for authorization to do the repair work. Retail customer must pay freight charge on parts to our plant and return. This warranty does not apply to any part, which is of the opinion of Ken-bar Mfg. Co., that rendered defective due to improper maintenance, improper assemble, alterations, abuse, negligence or accident. Warranty registration cards must be returned to Ken-bar. We will not honor a claim unless the card is mail to us within 10 days of purchase of Kart or Mini-Bike. Customer must view video after purchasing vehicle and put code number at end of video onto the registration card. To Order Ken-Bar Parts: You will need to use your breakdown illustration manual that came with your Ken-Bar machine Once you have found the part #(s) you need within your parts manual... Method 1 Direct Search: Type the part# into the search box (located on every page in the left side boxes) and then hit Enter on your keyboard (or click on the icon next to the search box). This will bring up the part or if more than one part starts with that string, a choice will be displayed. Click on the part (link) you need and a "Add to Cart" button will be displayed towards the bottom of the items listing. Method 2 Category Drill Down: More time consuming than above method but has it's use. Use the Category box (located in the upper left side on every page) Click on the Parts Dept > Ken-Bar Parts this will display the Parts Categories. Choose the proper Parts Category that encapsulates your part #. Click on the part (link) you need and a "Add to Cart" button will be displayed towards the bottom of the items listing.